Altivar 31 manual

[Armas]

Altivar 31 manual
.
.
Download / Read Online Altivar 31 manual
.
.
.

.
The email address you entered is not valid. Reach out to our customer support team to receive more information, technical support, assistance with complaints and more. Start your sales enquiry online and an expert will connect with you. Enter your email address and check your inbox. Please check your email for further instructions. Hazard Categories and Special Symbols . Power Up after a Manual Fault Reset or Stop Command . Test on a Low Power Motor or without a Motor . Operation on an Impedance Grounded System . Saving and Loading Configurations . Logic and Analog Input Application Functions . SIM, Combined Reference and Control . Automatic Operation with PI Regulator . Faults Which Cannot Be Automatically Reset . Faults Which Can Be Automatically Reset . Faults That Reset When the Fault Is Cleared . Drive Controller and Customer ID . A controllers throughout this manual. This manual contains programming instructions for ATV31 drive controllers. For example, SEtis a menu, but ACC is a parameter. The following symbols and special messages may appear in this manual or on the equipment to warn of potential hazards. An exclamation point symbol in a safety message in the manual indicates potential personal injury hazards. Obey all safety messages introduced by this symbol to avoid possible injury or death. For support and assistance, contact the Product Support Group. ATV31 drive controller into service. Make the following connections to the drive controller. Connect the grounding conductors. Power up the drive controller, but do not give a run command. Refer to page 12 for the factory settings. An input assigned to the run command may cause the motor to start immediately upon exiting the configuration menus. Failure to follow these instructions will result in death or serious injury. The designer of any control scheme must consider the potential failure modes of control paths and, for certain critical control functions, provide a means to achieve a safe state during and after a path failure. Examples of critical control functions are Emergency Stop and Overtravel Stop. Separate or redundant control paths must be provided for critical control functions. Failure to follow these instructions can result in death, serious injury, or equipment damage. Do not operate or install any drive controller that appears damaged. Failure to follow this instruction can result in equipment damage. The recommended method of control is through inputs LI1 to LI6. The motor thermal state memory returns to zero when line power is removed from the drive controller. DC injection stop commands must be reset for the drive controller to start. If they are not reset, the drive controller will display nSt and will not start. The drive controller will not provide motor thermal protection if the motor current is less than 0. The drive controller cannot provide adequate motor thermal protection for each motor. When using the drive controller on a system with an isolated or impedance grounded neutral, use a permanent insulation monitor compatible with nonlinear loads. These filters can be disconnected from ground when using the drive controller on an impedance grounded system to increase the operating life of their capacitors. Use the configuration settings tables beginning on page 91 to prepare and record the drive configuration before programming the drive controller. When first commissioning an ATV31 drive controller for a 60 Hz system, perform a factory parameter reset. The ATV31 drive controller is supplied ready for use in most applications, with the factory settings shown in Table 1. Running motors rated at less than 0. This equipment must be installed, programmed, and serviced only by qualified personnel. The application of this product requires expertise in the design and programming of control systems. Only persons with such expertise should be allowed to program, install, alter, and apply this product. CFR Part 1910 Subpart S Electrical. RESET key commands a freewheel stop. LOC, stopping is on a ramp, but if injection braking is in progress, a freewheel stop takes place. The display flashes when a value is stored. If a fault is present, the display flashes. If automatic restart is configured, the reset is not necessary. St and will not run until the run command is cycled and a valid speed reference is given. REV commands the direction of rotation. RESET commands the motor to stop or resets a fault. DC injection braking if it is configured. COMmenu must remain at the factory setting, 19. Password protection has priority over the access locking switch. For added convenience, some parameters can be accessed in more than one menu. Throughout this guide, a dash appears after menu codes to differentiate them from parameter codes. If you have modified a parameter in a menu and you return to that menu without accessing another menu in the meantime, you will be taken directly to the parameter you last modified. If you have accessed another m filexlib.
.
Altivar 31 met de hand
Altivar 31 handbook
Altivar 31 guide
Altivar 31 handbok
Altivar 31 brugervejledning

[投稿者]

投稿